Abstract
Automatic water level controller for both overhead and underground
tank is designed to monitor the level of water in a tank. It displays the
level of water and when it is at the lowest level; a pump is activated
automatically to refill the tank. When the tank is filled to its maximum
capacity, the pump is automatically de-energized. Several circuits are
put together to ensure proper working of this design, and the block
diagram includes the supply unit, the micro-processor unit, the sensor
unit, the display unit and the pump drives unit. The power unit is
responsible for turning on the entire circuit. Some components are
used to set up power unit and they include; a 15v step down
transformer, a bridge rectifier circuit, a smoothening capacitor and a
voltage regulator IC. The microprocessor (AT89S50) controls virtually
all the actions carried out in this design. (AT89S50) is used in the
design. The sensor unit is responsible for sensing the level of water
and transfer the
INTRODUCTION
1.0 BACKGROUND
The project “automatic water level control with an automatic pump
control system” is design to monitor the level of liquid in the tank. The
system has an automatic pumping system attached to it so as to refill
the tank once the liquid gets to the lower threshold, while offing the
pump once the liquid gets to the higher threshold. Sustainability of
available water resource in many reason of the word is now a dominant
issue. This problem is quietly related to poor water allocation, inefficient
use, and lack of adequate and integrated water management. Water is
commonly used for agriculture, industry, and domestic consumption.
Therefore, efficient use and water monitoring are potential constraint for
home or office water management system. Moreover, the common
method of level control for home appliance is simply to start the feed
pump at a low level and allow it to run until a higher water level is
reached in the water tank. This water level control, controls monitor and
maintain the water level in the overhead tank and ensures the
continuous flow of water round the clock without the stress of going to
switch the pump ON or OFF thereby saving time, energy, water, and
13
prevent the pump from overworking Besides this, liquid level control
systems are widely used for monitoring of liquid levels in reservoirs,
silos. Proper monitoring is needed to ensure water sustainability is
actually being reached with disbursement linked to sensing and
automation, such programmatic approach entails microcontroller based
automated water level sensing and controlling or using 555 timer IC.
1.1 AIMS AND OBJECTIVES
The goal or objectives of which the designed device is expected to
accomplish is to build an automatic water level control with automatic
control system. In this project sensors are place at different level of the
tank and with the aid of this sensors, the micro-controller monitor the
level of the liquid at any particular point in time, some of the objectives
are
1. to design an automatic water monitoring system
2. to incorporate an interactive medium between the end user and
the machine
3. to prevent over labor of the pumping machine and prevent it from
getting bad
4. to avoid wastage of water
14
5. since the demand of electricity is very high, automatic water level
control saves energy
1.2 JUSTIFICATION
Automatic water level monitor came into existence because of human
error and inconsistence that is associated with manually operated water
pumping machine. This is because it takes time for individual who is
manually operating the water pump to turn off the pumping machine and
this may cause water spillage and at times the individual might not know
that the water level has drop so low until the tank is completely empty.
This was the problem that leads to the development of the ideal of an
automatic water level control and automatic pump short down.
1.3 SCOPE OF THE PROJECT
The project was design to automatically control the pump which ensures
constant reserve of water in the reservoir. The scope of the design was
keep concise and simple to in other not to introduce unnecessary
complexities and render it generally uncomfortable. The system does not
have attached complex peripheral device which though impossible for the
detail printable information has been excluded for reasons of affordability
material of low range and less accurate performances as opposed to a
15
well built automatic water pump was use d to achieve this aim, the
automatic water level controller detect and control the water in the tank
1.4 CONSTRAINS
The biggest setback experience during the course of this project is
difficulties in finding the design of the project, secondly sourcing of
material and component I used for the project were difficult to find like
pump and buffer for programming
1.5 LIMITATIONS OF THE PROJECT
It is significant to know that this design is limited to 12v, 5amps electric
pump and cannot be use to control industrial water pump above 5 amps
BLOCK DIAGRAM OVERVIEW
This project report writing is written is design in such a way that each
chapter is related to the next as shown below
FIG 1.0 BLOCK DIAGRAM OF AUTOMATIC WATER LEVEL
CONTROL WITH PUMP
POWER SUPPLY
UNIT
CONTROL
UNIT
DISPLAY
UNIT
INPUT UNIT
CONTROL
UNITE
16
1.6 PROJECT RESPORT ORGANISATION
The organization of this project report is well detailed and vast in its
coverage it covers all the activities encountered during the research
work. The first chapter of this work took care of the introduction, aims
and objective, scope, Justification and project report organization.
Chapter two highlight on literature review chapter three highlight on
description of system and some of the component used were emphasized
chapter four highlight on the system design and implementation,
construction, testing and packaging of the pump. Chapter five is all about
the conclusions problem encountered recommendation and cost of the
project.